Product List
- Engine Spare Parts
- Cylinder Block
- Cylinder Liner
- Camshaft Bush
- Main Bearing
- Timing Gear Box
- Front Crankshaft Oil Seal
- Oil Cooler Cover
- Flywheel Housing
- Crankshaft
- Crankshaft Gear
- Flywheel
- Flywheel Ring Gear
- Crankshaft Shock Absorber
- Piston
- Piston Pin
- Connecting Rod
- Piston Ring
- Connecting Rod Bearing
- Cylinder Head
- Cylinder Head Gasket
- Camshaft
- Middle Gear
- Exhaust Air Valve
- Air Intake Valve
- Water Pump
- Fan Blade
- Thermostat
- Oil Pump
- Oil Pump Valve
- Oil Cooler Element
- Oil Filter Element
- Coupling
- Oil Injector
- Fuel Filter Element
- Gear Reduction Starter
- Alternator
- Electromechanical Oil Pressure Sensor
- Water Temperature Gauge Sensor
- Front Air Exhaust Pipe
- Rear Air Exhaust Pipe
- Turbocharger
- Double Cylinder Air Compressor
- Oil Pan
- Chassis Spare Parts
- Clutch Spare Parts
- Automobile Interior Trim Parts
- Exterior Car Accessories
- Gear Box Spare Parts
- Other Parts
Cylinder Block
Introduction
Cylinder block is the basic structure of the engine and works as an important component. It sits between the cylinder head and the oil pan. In a broad sense, it is an integrity part made up of several engine blocks and a crankcase. We offer various kinds of cylinder block, including: Weichai power cylinder block, Yangzhou Naimo cylinder block, Sinotruk engine cylinder block, Laiyang Zhonggao cylinder block, etc. They can be used in WD 618.420, WEBB Euro II, WP10 EGR, WP10 Common Rail, WP12.4 Valve, EGR.2 trucks engine.
Advantages
1. It is made from stainless steel (304, 316, 3041, 3161 etc.) and carbon steel.
2. The engine blocks are mainly processed at horizontal machining centers. During cylinder block production, only a few procedures are handled at vertical machining centers.
3. Engine block surface is milled in professional way, so is front surface of main bearing seat and bearing fixing groove.
4. Idler shaft, lubrication-oil duct, water cooling channel and fuel filter are drilled by a special driller.
5. Broach is used during processing of cylinder block. It assures accuracy of main bearing seat.
6. Boring cutter is applied to process bores on main bearings, cams and cylinder liners.
Name | Cylinder Block (Weichai Power, Yangzhou Naimo, Sinotruk Engine, Laiyang Zhonggao) | |||||
Number | 61800010109 | 61500010816 | 612600900039 | 612600900029 | 612630010396 | AZ1095010033 |
Applicable Engine | WD618.420 | WEVB Euro II | WP10 EGR | WP10 Common Rail | WP12.4 Valve | EGR.2 |
Manufacturer | Weichai Power | Yangzhou Naimo | Yangzhou Naimo | Yangzhou Naimo | Weichai Power | Sinotruk / Laiyang Zhonggao / Yangzhou Naimo |
Lantoky Truck Parts is a supplier of Weichai Power cylinder blocks (WD618, WP12, WP10, etc.), Yangzhou Naimo cylinder block, Sinotruk engine cylinder block, Laiyang Zhonggao cylinder block. Located in Jinan City, the main production base of heavy trucks in China, it has accumulated abundant experience and advanced service quality a lot since its foundation in 2003.
Related Products
- Cylinder LinerCylinder liner, or cylinder sleeve, is a device that is pressed into an engine block and used to house the piston. This engine spare part has stronger hardness than engine block and it prevents piston from wearing through cylinder bores. In aluminum engine blocks and diesel engines, it is pressed into position or held in place by the cylinder head. In large engines, such as engines of diesel locomotives...